Episode 8 – How To Wire And Install 4-Way Switches

In this video I talk about how to wire for and install 4-way switches.  4-ways are very similar to 3-ways, and in fact you use (2) 3-way switches in a 4-way setup.

First you have to think about the reason why you need a 4way.  4way setups are needed when you have 3 or more locations that need to be able to switch the same light or lights.  Say you have a room with 3 entrances/exits.  You will need to place a single gang box at each of the 3 doorways for a switch to go.  In a 3way setup you only need 2 boxes because you’re only trying to control a light from 2 locations.

Once you get the 3 boxes set up you need to figure out which side will be your “hot side,” and which will be your “leg side.” The hot side is where your incoming power will land.  Your leg side is where your switch leg will go up to the light or lights you’re trying to control.  You want to be sure not to put both your hot and your leg in the same box.  Always keep them on separate sides of the room.

From the hot side you’ll run a 12/3 “traveller” (3-conductor with ground – most often a black, red, white, and bare ground) from the first switch box to the 4-way switch box in the middle.  Then from that middle 4 way box you’ll run another 12/3 traveller out to your leg-side box.  Then if you haven’t already run a hot (12/2) to your hot side box from a known location of existing power.  Finally run a switch leg (12/2) from your leg side box up to the light/lights.

That’s it as far as the wiring.  It is a good practice to get into to label each wire that you land in a box.  You won’t need to do this up in the light or in any plug boxes.  Only light switch boxes need to be labelled when wiring for a 3–way or 4-way system.

Next you’ll need to rip out the wires and prepare them for installing the 3way and 4way devices.  This video talks about properly twisting grounds together, making joints on the neutrals, and twisting your 12/3 black and red wires together to identify them as travelers.  Otherwise you may get confused about which black wire goes where.  

Once you have everything ripped out and prepared for the switches, it’s time to install the devices.  On the 3way switches (one goes on the hot side, the other goes on the leg side) you’ll simply put the independent black wire on the black (common) screw.  Both of the gold screws are for the 12/3 travellers.  And finally the green screw is for the bare ground.

The 4-way switch goes in your middle box and each pair of 12/3’s go to a specific side of the 4way device.  Each 4-way switch has an “IN” and “OUT” side designated on the back of the device.  Make sure that the travelers coming from the hot side go into the “IN” terminals.  The travelers going out to the leg side must go in the “OUT” terminals.

Once all of the devices are installed turn on power (make sure you have a lightbulb in your light) and start flipping all of the switches you just installed.  You should be able to walk through the room and flip every switch and all of them both turn on and off the lights from all 3 locations.  If not, you fucked something up lol

A 4way system can have an infinite amount of switches.  If you have a room that needs 8 switches (for some stupid reason), you would still be able to use this set up.  If you have any questions on how to do this, please leave a comment below and I’ll happily explain how this would work.

Thanks for watching!


If you enjoy these episodes please click SUBSCRIBE and LIKE these videos!  Also check out the Journey 2 Master podcast on iTunes, Google Play Music, SoundCloud, iHeartRadio, OverCast and Stitcher!


  1. This is a great resource! I appreciate all of your content, and the time you take to put all of this together. I am an apprentice, and being completely honest the electrician I’m working under does not want to teach the trade. He doesn’t want to feel replaceable. All of your content is helpful and I hope you continue!

    1. Man I’m glad you’re into this trade, but it sucks that guy you’re working under isn’t taking your training seriously. That makes a huge difference in a person’s desire to stick around and how far they want to take their knowledge. I’d recommend trying to work under a different person if you can. If not at this company, there are other companies out there. Keep your head up!

  2. Hi Dustin!

    Got a question I could not find the answer and was wondering if you could help me?
    I come from Europe and therefore I want to make sure I’m going to do this work correctly!

    I have a fan and 2 lights in series above sink + light above shower. I only have 2 switches, one for the lights and the other for the fan.

    I would like to separate my lights into 2 switches. Can you please help me with the correct diagram? I really would appreciate it so very much!
    Would love to send you a picture or my schematic but honestly do not know how to add it to this window, truly sorry!

    Can you please help me?
    Thank you for your consideration and time.

    Best regards!

    Great teaching! If I was younger, I would have loved to become an electrician but the military put me in Electronics…

    Thank you in advance!


Leave a comment